Use of Taguchi Methods for Hierarchy of Influence Factors in the Application of Carbonitration in a Fluidized Bed Steel for 41Cr4 Steel

  • Nelu CAZACU "Dunarea de Jos" University of Galati, Romania
Keywords: fluidized bed, Taguchi method (T M), 41Cr4, carbonitriding

Abstract

The work is based on carbonitriding in a fluidized layer with methane and ammonia gas applied to 41Cr4 steel samples. To achieve the best possible results, other factors must be taken into account, than those specific to carbonitring. It was necessary to use a partially factorial working procedure due to the increase in the number of factors. An A18 matrix has been used, with 18 lines of experiments in which three levels have been modified for 6 factors. The objective function was fixed at the final hardness after carbonitriding, hardening and tempering. The carbonitriding was performed in fluidized bed with granular solid ground and sorted to 0.1- to 0.16mm, and brought to fluidization with a mixture of methane and ammonia. The hardening has been done directly after carbonitriding in the fluidized bed. The experiments have been performed according to Taguchi Methods and the results indicate an optimal regime and the influence of the factors considered on the hardness after the thermo-chemical treatment and the thermal treatment. Metallographic analysis has been performed on the carbonitrided layer.

Creative Commons License

Downloads

Download data is not yet available.

References

[1]. ***, ASM Handbook. Heat Treating, vol. 4, s.l., ASM International, ISBN 0-87170-379-3, 1991.
[2]. Dobrovici Sorin, Bâclea Adolf, Weight Factors over Carbonitriding in Fluidized Bed for 40Cr10 Steel, The Annals of ”Dunarea de Jos” University of Galati, Fascicle IX, Metallurgy and Materials Science, p. 70-74, ISSN 1453-083X, 2002.
[3]. Dobrovici Sorin, Cazacu Nelu, Some Aspects of 40Cr10 Steel Behavior on Fluidized Bed Carbonitriding, The Annals of ”Dunarea de Jos” University of Galati, Fascicle IX, Metallurgy and Materials Science, p. 17-22, ISSN 1453-083X, 1999.
[4]. Bâclea Adolf, et al., Surface Hardening of 40Cr10 Steel After Short Time Nitriding in Fluidized bed, The Annals of ”Dunarea de Jos” University of Galati, Fascicle IX, Metallurgy and Materials Science, vol. 2, p. 40-44, ISSN 1453-083X, 2006.
[5]. ***, ITTSF paper.
[6]. Taguchi G., Introduction to quality engineering into products and processes, s.l.: Asian productivity organization, 1986.
[7]. Logothetis N., Wynn H. P., Quality through design, Oxford: Clarendon Press, ISBN 0 19 859395 3, 1994.
[8]. Phadke M. S., Quality engineering using robust design, Englewood Cliffs, New Jersey: Prentice Hal, 1989.
[9]. Samoila C., Ionescu M.S., Drugă L., Tehnologii şi utilaje moderne de încălzire, București: Editura Tehnică, 1986.
[10]. Vermeşan G., Tratamente termice, Indrumător, Editura Dacia: Cluj Napoca, 1987.
[11]. Popescu N., Vitănescu C., Tehnologia tratamentelor termice, București: Editura Tehnică, 1974.
[12]. Mihăilă C., Procese termodinamice în sisteme gaz-solid şi aplicaţiile lor în industrie, Bucureşti: Editura Tehnică, 1983.
[13]. Kunii D., Levenspiel O., Fluidization engineering, New York, John Wiley & Sons, Inc., 1969.
[14]. Baskakov A. P., Nagrev I ohlajdenie metallov v kipiasciem sloe, Moscova: Metalurghia, 1974.
[15]. Ivanuş Gh., Todea I., Pop Al., Nicola S., Damian Gh., Ingineria fluidizării, Bucureşti, Editura Tehnică, 1996.
[16]. Esayan L., Esayan M., Fluidizarea, Editura Tehnică, Bucureşti, 1959.
[17]. Samoila C. Drugă, Stan I., Cuptoare şi instalaţii de încălzire, Bucureşti, Editura Didactică şi Pedagogică, 1983.
[18]. Bâclea Adolf, Dobrovici Sorin, Quality Engineering Applications on the Nitriding Steel in Fluidized Bed, The Annals of ”Dunarea de Jos” University of Galati, Fascicle IX, Metallurgy and Materials Science, p. 81-87, ISSN1453-083X, 2002.
Published
2021-09-15
How to Cite
1.
CAZACU N. Use of Taguchi Methods for Hierarchy of Influence Factors in the Application of Carbonitration in a Fluidized Bed Steel for 41Cr4 Steel. The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science [Internet]. 15Sep.2021 [cited 31Oct.2024];44(3):36-7. Available from: https://gup.ugal.ro/ugaljournals/index.php/mms/article/view/4873
Section
Articles

Most read articles by the same author(s)

<< < 1 2 3 > >>